This also applies to times that end up in that json.
Where applicable moved time.Now() to where it is used.
Moved calls to .UTC() to where time is created it that time is converted
later anyway.
Signed-off-by: Matthias Hanel <mh@synadia.com>
This moves from explicit imports and subscriptions to one wildcard subscription and a single wildcard export.
Signed-off-by: Derek Collison <derek@nats.io>
The new endpoints are /jsz on http and "$SYS.REQ.SERVER.PING.JSZ" and "$SYS.REQ.SERVER.%s.JSZ".
$SYS.REQ.ACCOUNT.%s.JSZ will only return info for the particular account
Signed-off-by: Matthias Hanel <mh@synadia.com>
Only the user (from username/password connection method) was reported
in this monitoring endpoint. Will now report proper nkey, public key,
etc..
Resolves#1799
Signed-off-by: Ivan Kozlovic <ivan@synadia.com>
This PR introduces native support for MQTT clients. It requires use
of accounts with JetStream enabled. Since as of now clustering is
not available, MQTT will be limited to single instance.
Only QoS 0 and 1 are supported at the moment. MQTT clients can
exchange messages with NATS clients and vice-versa.
Since JetStream is required, accounts with JetStream enabled must
exist in order for an MQTT client to connect to the NATS Server.
The administrator can limit the users that can use MQTT with the
allowed_connection_types option in the user section. For instance:
```
accounts {
mqtt {
users [
{user: all, password: pwd, allowed_connection_types: ["STANDARD", "WEBSOCKET", "MQTT"]}
{user: mqtt_only, password: pwd, allowed_connection_types: "MQTT"}
]
jetstream: enabled
}
}
```
The "mqtt_only" can only be used for MQTT connections, which the user
"all" accepts standard, websocket and MQTT clients.
Here is what a configuration to enable MQTT looks like:
```
mqtt {
# Specify a host and port to listen for websocket connections
#
# listen: "host:port"
# It can also be configured with individual parameters,
# namely host and port.
#
# host: "hostname"
port: 1883
# TLS configuration section
#
# tls {
# cert_file: "/path/to/cert.pem"
# key_file: "/path/to/key.pem"
# ca_file: "/path/to/ca.pem"
#
# # Time allowed for the TLS handshake to complete
# timeout: 2.0
#
# # Takes the user name from the certificate
# #
# # verify_an_map: true
#}
# Authentication override. Here are possible options.
#
# authorization {
# # Simple username/password
# #
# user: "some_user_name"
# password: "some_password"
#
# # Token. The server will check the MQTT's password in the connect
# # protocol against this token.
# #
# # token: "some_token"
#
# # Time allowed for the client to send the MQTT connect protocol
# # after the TCP connection is established.
# #
# timeout: 2.0
#}
# If an MQTT client connects and does not provide a username/password and
# this option is set, the server will use this client (and therefore account).
#
# no_auth_user: "some_user_name"
# This is the time after which the server will redeliver a QoS 1 message
# sent to a subscription that has not acknowledged (PUBACK) the message.
# The default is 30 seconds.
#
# ack_wait: "1m"
# This limits the number of QoS1 messages sent to a session without receiving
# acknowledgement (PUBACK) from that session. MQTT specification defines
# a packet identifier as an unsigned int 16, which means that the maximum
# value is 65535. The default value is 1024.
#
# max_ack_pending: 100
}
```
Signed-off-by: Ivan Kozlovic <ivan@synadia.com>
There was a test to prevent an errorneous loop detection when a
remote would reconnect (due to a stale connection) while the accepting
side did not detect the bad connection yet.
However, this test was racy because the test was done prior to add
the connections to the map.
In the case of a misconfiguration where the remote creates 2 different
remote connections that end-up binding to the same account in the
accepting side, then it was possible that this would not be detected.
And when it was, the remote side would be unaware since the disconnect/
reconnect attempts would not show up if not running in debug mode.
This change makes sure that the detection is no longer racy and returns
an error to the remote so at least the log/console of the remote will
show the "duplicate connection" error messages.
Resolves#1730
Signed-off-by: Ivan Kozlovic <ivan@synadia.com>
The mappings enable traffic shaping functionality.
Also added a subject transform which can match any subject and transform to a new one, even re-ordering partial wildcards.
Signed-off-by: Derek Collison <derek@nats.io>
Returned imports/exports are formated like jwt exports imports, even if
they originating account is from config.
Fixes#1604
Signed-off-by: Matthias Hanel <mh@synadia.com>
Leafnodes that formed clusters were partially supported. This adds proper support for origin cluster, subscription suppression and data message no echo for the origin cluster.
Signed-off-by: Derek Collison <derek@nats.io>
