The issue is that the consumer info returned by the consumer create
API is gathered after the consumer is added and possibly after
starting to deliver pending messages.
Signed-off-by: Ivan Kozlovic <ivan@synadia.com>
If the consumer's sequence was not the same than the stream's sequence,
then the redelivery would always use the first duration from the
BackOff list.
Signed-off-by: Ivan Kozlovic <ivan@synadia.com>
Currently this code returns a 200 and { "status": "ok" } iff all configured ports are open
and if JetStream is configured and we have contact with the metaleader and the cluster and all streams are up to date.
Signed-off-by: Derek Collison <derek@nats.io>
This allows a consumer to have exponential backoffs vs static AckWait and MaxDeliver.
When BackOff is set it will overridde AckWait to BackOff[0] and MaxDeliver will be len(BackOff)+1.
Signed-off-by: Derek Collison <derek@nats.io>
We will only send if all peers in our group are >= 2.7.1 and we will check for updates.
When a consumer follower takes over it will notify all pending requests that those requests are invalid now.
Signed-off-by: Derek Collison <derek@nats.io>
Under load we could have a message committed to the underlying store when a consumer was being created and then it increase num pending again when the stream signals the consumers.
This fix just remembers the last seq of the state when we calculate sgap and test before adding in the stream code.
Signed-off-by: Derek Collison <derek@nats.io>
Cleaned up code, made more consistent, utilize loopAndGather.
Allow pull consumers to have AckAll as well as AckExplicit.
Signed-off-by: Derek Collison <derek@nats.io>
This allows stream placement to overflow to adjacent clusters.
We also do more balanced placement based on resources (store or mem). We can continue to expand this as well.
We also introduce an account requirement that stream configs contain a MaxBytes value.
We now track account limits and server limits more distinctly, and do not reserver server resources based on account limits themselves.
Signed-off-by: Derek Collison <derek@nats.io>
If the interest existed prior to the initial creation of the
consumer, the gateway "watcher" would not be started, which means
that interest moving across the super-cluster after that would
not be detected.
The watcher runs every second and not sure if this is costly or
not, so we may want to go a different approach of having a separate
interest change channel that would be specific to gateways. But this
means adding a new sublist where the interest would be registered
and that sublist would need to be updated when processing GW RSub
and RUnsub?
Signed-off-by: Ivan Kozlovic <ivan@synadia.com>
Along a leaf node connection, unless the system account is shared AND the JetStream domain name is identical, the default JetStream traffic (without a domain set) will be denied.
As a consequence, all clients that wants to access a domain that is not the one in the server they are connected to, a domain name must be specified.
Affected from this change are setups where: a leaf node had no local JetStream OR the server the leaf node connected to had no local JetStream.
One of the two accounts that are connected via a leaf node remote, must have no JetStream enabled.
The side that does not have JetStream enabled, will loose JetStream access and it's clients must set `nats.Domain` manually.
For workarounds on how to restore the old behavior, look at:
https://github.com/nats-io/nats-server/pull/2693#issuecomment-996212582
New config values added:
`default_js_domain` is a mapping from account to domain, settable when JetStream is not enabled in an account.
`extension_hint` are hints for non clustered server to start in clustered mode (and be usable to extend)
`js_domain` is a way to set the JetStream domain to use for mqtt.
Signed-off-by: Matthias Hanel <mh@synadia.com>
When creating the http server, we need to provide a TLS configuration.
After a config reload, the new TLS config would not be reflected.
We had the same issue with Websocket and was fixed with the use
of tls.Config.GetConfigForClient API, which makes the TLS handshake
to ask for a TLS config. That fix for websocket was simply not applied
to the HTTPs monitoring case.
I have also fixed some flappers due to the use of localhost instead
of 127.0.0.1 (connections possibly would resolve to some IPv6 address
that the server would not accept, etc..)
Signed-off-by: Ivan Kozlovic <ivan@synadia.com>
1. When a snapshot did not yield actionable data, we were not setting new last sequence if we have to readjust based on snapshot. This could lead to spinning on stream reset for followers.
2. When a stream has lots of failures by design, like KV abstraction, if we cleared the clfs state we would endlessly spin trying to reset the stream.
Signed-off-by: Derek Collison <derek@nats.io>
When encountering errors for sequence mismatches that were benign we were returning an error and not processing the rest of the entries.
This would lead to more severe sequence mismatches later on that would cause stream resets.
Also added code to deal with server restarts and the clfs fixup states which should have been reset properly.
Signed-off-by: Derek Collison <derek@nats.io>
When a socket is bound for IP stack protocols with port == 0, the kernel picks
a free port in a specific range and binds it; on Linux, the range can be seen
(and modified) with `sysctl net.ipv4.ip_local_port_range` or looking in
`/proc/sys/net/ipv4/ip_local_port_range`. This defaults to 32768:60999.
When binding explicit ports (for tests), don't use a port number from that
range, or there will be flaky tests as periodically that port will already be
in use from another test.
This renumbers all the JS clustering tests I found binding in that range to be
beneath that range; I checked the code to ensure the new port wasn't already in
use.
There was a bug that would erase the sync subject for upper level catchup for streams.
Raft layer repair was ok but if that was compacted it gets kicked up to the upper layers which would fail.
Users would see "Catchup stalled" messages repeatedly and consumers that had their leaders attached to that replica would also stop working.
Changes were put in to repair the corrupt state after the fact as well, regardless of presence of fix.
Signed-off-by: Derek Collison <derek@nats.io>
Messages published with the rollup header will place the new message onto the stream and purge all others based on subject, or the complete stream.
Signed-off-by: Derek Collison <derek@nats.io>
Sealed streams can not accept new messages, allow you to delete or purge messages, or have messages expire due to age.
Sealed stream can not be unsealed through an update.
Signed-off-by: Derek Collison <derek@nats.io>
